01
Natural Touch
Stone-like tactile texture
A mineral, tactile hand-feel for stone-inspired surfaces. Fine relief under the fingertip, no reflection.
Fabrication
Good fabrication depends more on parameters than on the slab itself. Equipment selection, cutting speeds, edge work and batch practice — follow these and you will cut rejections and waste, not the other way round.
Hardness
Mohs ≥ 6
Quartz-equivalent; standard tooling
Heat resistance
> 300 °C
Direct contact with hot pans; unaffected by residual flame
Water absorption
≤ 0.5 %
Full-body porcelain; no absorption or staining
Dimensional stability
无翘曲
No warping on long slabs or multi-cut batches
★ Parameters on this page are industry reference values, not our own measured data. Verify against your plant's documentation before production use.
Equipment
Fabrication equipment
桥切走直线与拼角，水刀走异形与开孔，CNC 走精确孔位，角磨收边。设备选对了，废品率降一半。
Infrared bridge saw
Straight and mitre cuts
- Spec
- 1.5–3.0 m/min · 6–20 mm · digital guide
- Tip
- Always water-cool to avoid edge chipping
Waterjet cutter
Curves, holes, 45° bevels
- Spec
- ≥ 300 MPa · 0.5–1.2 m/min · flat slab feed
- Tip
- Best for shapes and fragile slabs; keep the feed flat
CNC / Drill
Arcs, tap holes, precision cut-outs
- Spec
- > 18 mm holes · 0.8–1.5 m/min · step drilling
- Tip
- Water cooling mandatory; never dry-drill
Angle grinder
Edge shaping and polishing
- Spec
- Diamond pad 50–3000#
- Tip
- Step between grits; wet polishing gives the deeper gloss
Parameters
Parameter quick reference
速度为常用区间，实际参数须按设备、刀具与板厚验证。
| Machine | Process | Speed / Feed | Best tip |
|---|---|---|---|
| Bridge saw | Straight / mitre | 1.5–3.0 m/min | Drop to 0.8–1.5 m/min at the edge; water-cool throughout |
| Waterjet | Irregular / cut-out / bevel | 0.5–1.2 m/min | ≥ 300 MPa; keep the feed flat and even |
| CNC / drill | Arc / tap hole | > 18 mm · 0.8–1.5 m/min | Step-drill with water cooling to avoid stress cracks |
| Angle grinder | Edge polish | 手动 · 50–3000# | Do not skip grits; finish wet |
Best practice
Best practice
这六条是加工端最常见的翻车点。做到位，能显著降低崩边、开裂与报废。
Trim 2 cm off each edge first
Releases internal stress and improves yield
Support flat and soft; check flatness first
Rubber or timber beds to absorb cutting vibration
Wet-cut and wet-drill only; replace worn tooling
Dry cutting chips edges and kills blade life
Back mitred edges with fibreglass mesh
Spreads stress to prevent long counters from cracking
Test-cut new patterns before batch runs
Confirm layout and tool path before committing volume
Store on A-frames or flat, indoors and dry
Avoid long-term tilt and moisture exposure
Applications
Kitchen countertop / islandBathroom vanityTabletop / furnitureWall cladding / features
Surface finishes
Nine finishes, one clearer way to compare them
柔光和哑光写在参数表里谁也分不清，看一眼实拍纹理立刻明白。选工艺时先看采光与清洁习惯，再定光泽度。
01
02
03
04
05
06
07
08
09
★ Procedural placeholders here — swap for macro photographs and the finish differences read far more clearly.
Packing & loading
Packing and container loading
包装方式按产品形态选，成品件与板材的包装逻辑完全不同。装柜按四步走，能最大化柜内空间并减少途中移位。
01
Wooden bundle
Standard bundled packing with corner guards and timber bearers. Best value for long sea freight.
02
A-frame packing
Upright frames for large slabs. Prevents warping; suits 3200 mm formats and project-scale orders.
03
Carton and pallet
For finished and fabricated pieces — countertops, basins, cabinet fronts. Far less handling damage.
01
Initial positioning
First layer set to the drawing direction, with proper spacing and alignment references.
02
Systematic loading
Loaded layer by layer against the packing list to maximise container use.
03
Secure fastening
Steel straps, timber bracing and corner guards to prevent movement in transit.
04
Final inspection
Verify piece count and packaging integrity; photograph before the doors close.
Need parameters for your project?
Send us the thickness, dimensions and your equipment situation. Our technical team returns a processing plan with a yield estimate.